
Foreign exchange costs have pushed almost every flexible packaging plant in Lagos, Aba, and Kano onto locally extruded recycled polyethylene. Blending regrind is what keeps shopping bags, pure water sachets, and bread wrappers affordable, so the material is not going away. What has to change is how the press is set up for it.
Recycled film brings three problems at once: thickness that varies, gels that sit proud of the surface, and surface oils that push ink away. Add grid fluctuations and generator running, and the result is web breaks that cost an hour of re-threading, white dots across solid backgrounds, and a shift that produces less than it should.
Regrind has been melted more than once. Dust, carbon specks, and unmelted fragments survive into the film, and the extruder turns them into hard lumps and thickness variation. A web that varies in gauge also varies in strength, and it will always break at the thin point.
Surface chemistry is the second issue. Recycled resin carries slip agents, moisture, and oily residue, and those migrate to the surface while the roll sits in a hot warehouse. Ink does not wet a surface like that, so it pulls away and leaves craters.
It is worth separating two defects that get called the same thing. A white dot where ink did not transfer is usually a gel or a dust particle holding the plate a fraction off the film — the film itself is intact. A true pinhole is a hole through the web, from moisture vapour, contamination, or a damaged die lip. Hold the film up to the light: light passes through a hole, not through a gel.
The two need different fixes, and treating a film hole as an ink problem wastes a shift.
Virgin film tolerates aggressive pulling and hot tunnels. Recycled film does not, because it stretches unevenly and fails at its thin spots. Bringing the unwind brake tension down and trimming peak line speed lets the web run without the jerks that precede a break.
Running slower reads as lost output, but two breaks per shift cost more than the speed does — an hour of re-threading, plus the diesel and power spent getting back on register.
Oven heat is the other lever. Softening recycled film in a hot tunnel turns it elastic, and an elastic web stretches until it snaps, usually inside the dryer where nobody can see it coming. Cut the tunnel temperature and make the exhaust do the work instead: solvent removal is an airflow job as much as a heat job.
White rings around gels respond to impression before they respond to ink. A slightly softer sticky-back under the flexo plate, or a softer impression roller on gravure, lets the nip cushion around a bump instead of lifting off it.
Ink consistency comes second. A marginally thicker ink covers small surface valleys more forgivingly than a thin one, but keep it inside the range the anilox will transfer — pushing viscosity too far trades white dots for poor laydown.
Corona is the step most plants skip and should not. Recycled film loses surface energy faster than virgin material, so treat every roll inline before the first colour station to burn off the oils and bring the dyne level back to target. Check it with a dyne pen as the roll runs, because the number drifts with storage time.
Corona also deserves respect. Isolate the unit before cleaning electrodes, keep the interlock working so the discharge stops when the guard opens, and duct the ozone outdoors — it is a respiratory irritant and it corrodes the pressroom.
Dust is a maintenance problem on recycled stock. The film sheds flakes into the ink pan, and those clog anilox cells and doctor blades, which shows up as more white dots. Clean the pans and blades on a fixed schedule rather than when the print degrades.
None of this fixes a bad roll. The press can compensate for variation and gels, but it cannot remove them, so the incoming specification matters as much as the machine settings.
Agree a gel count and a minimum dyne value with the extruder, and ask what melt filtration they run — a finer screen pack at the film stage removes more of what becomes a white dot at the press. Rolls that arrive below spec should go back rather than into a job.
Handling is part of the fix too. Stop the press and lock it out before re-threading, and never reach into a nip while the web is moving; a running press will take a hand faster than it takes film.
Slower tension, cooler tunnels, softer impression, fresh corona, and a spec on the roll. That is how recycled film prints clean instead of costing you a shift every week.
If your plant is fighting breaks and white dots on recycled stock, or you are specifying presses and corona treaters for Nigerian film supply, our technical team would be glad to review your setup.

How to Protect Your

How to Fix Print Def

How Cheap Adulterate

How to Stop Poor Ope